The vibrating screen installation and debugging is important for the vibrating screener users. If can influence the working life of vibratory screen and the quality of final products. So the installation and debugging played an important role in course of vibrating screen operation. So today we will talk about the vibrating screen installation and debugging in order to make the user know more about the vibrating screener working.
1) Pre-installation preparation
The new equipment, vibrating screen prior to installation, should be carefully scrutinized. As the manufacture of finished goods inventory piling up a longer time, such as rusted bearings, seals, aging or damaged during handling and so on, faced with these problems need to be replaced new parts. Also, as exciter, and the factory for rust-proof, injection of anti-rust oil, formally put into operation before the replacement into lubricating oil.
Instructions should be read carefully before installation, make full preparations.
2) The installation
(1) Installation of supporting or hanging device. Installation, to foundation leveling, and then supporting or hanging device in accordance with parts drawings and installation diagram sieves, in order to install the components.
(2) sieve box connected to the supporting or hanging device. Bottles and later, should be required to adjust the angle. For the hanging of the sieve, it should also adjust the screen angle and screen box spindle box level. Levels after correction, and then adjust the vertical inclination of sieve box. Vibration isolation spring force should be uniform, which could force the situation by measuring the amount of spring compression to judge. General, two sets of feed-side of the compression spring to be the same two sets of springs discharging side should also be the case. Nesting side and feed side may be differences in the amount of spring compression.
(3) Installation of electric motors and the triangle tape. Installation, leveling should be based on the motor, motor level of need for correction, two tape round the
corresponding grooves of the center line should coincide, triangular tension dictate the appropriate tape. rotary kiln:http://www.hx-china.com/19.html
(4) Required to install and fixed-screen surface.
(5) Check the connection sieve components (such as the sieve plate, exciter, etc.) a fixed situation, screen should be uniform. tension, in order to prevent the generation of local vibration. Check the transmission part of the lubrication conditions, the motor and control box wiring is correct, and the rotation transmission part of the hand to see whether it is normal operation.
(6) Check the entry sieve materials, discharge chute and the funnel at work the next screen whether a crash.
Screening machine installed, commissioning should be empty, the initial check installation quality, and make the necessary adjustments.
(1) Shall not be less than the sieve empty commissioning time 8h. In this time, the observation of sieve quickly whether to initiate a smooth, vibration and stability of operation, no special noise amplitude by the amplitude to observe its compliance with licensing requirements.
(2) The sieve operation, the vibrating screen box should not result in yaw. In case of yaw, which may be due both sides of the spring height difference is too large, hanging rope pull uneven rotation axis is not horizontal or triangular tape too tight, should be adjusted accordingly.
(3) Driving 4h, the bearing temperature is rising, and then remained stable. The maximum temperature does not exceed 75, temperature should not exceed 40.
(4) If abnormal noise or driving after a sharp increase in bearing temperature should be immediately shut down, check whether the rotation axis is a flexible and well lubricated and so on, until after the start troubleshooting.
(5) 2-4h after driving down to check whether there are loose connection parts, if there are loose, tighten until after the drive.
Automatic foam cutting can be done either with a CNC hot wire foam cutter, a CNC laser cutter or a CNC router. The first two will cut 2D cuts, while the router will cut 3D shapes. The type of machine to be used for cutting is based upon the type of foam to be cut, its thickness and its size. More >>
Are you the kind of person who likes to take a lot of fashion risks? Do you love to wear unique looking clothes and accessories? The jewelry you wear will also be quite unique if you are a fashion forward person. More >>
Students Looking To Buy Professional and Custom Essays To enjoy Massive Price Cuts After Leading Provider Buyingessays.com Confirmed 20% Discount More >>
The writers are always busy in writing and editing their works. They will not have much time to spend on publishing and marketing their books and the new writers will not know the process of publishing a book. More >>
Regardless if you are a business owner or possibly a person citizen, obtaining a skilled, knowledgeable accountant designed for taxes help or dealing with IRS tax problems is extremely important. More >>
Ball mills the improved economic benefit: after improvement, material conveying uniform, and improves the production efficiency. More >>
As both the global resources business and the Russian economy are changing, the Russian mining industry will change. Two key trends will shape the development of the industry in the next decade: a struggle for competitiveness, increasing productivity and investing in new technology, and internationa More >>
Pollution Chemicals like mercury, cyanide, sulfuric acid, arsenic and methyl mercury are used in various stages of mining. Most of the chemicals are released into nearby water bodies, and are responsible for water pollution. More >>
From roof tiles and patio slabs to structural beams and columns, concrete is the basis for many construction applications and its use is growing. According to the International Energy Agency, global cement demand by 2050 will be between 3.69 - 4.4 billion tones. More >>
Mining is the extraction of valuable minerals or other geological materials from the earth, from an ore body, vein or (coal) seam. The nature of mining processes creates a potential negative impact on the environment both during the mining operations and for years after the mine is closed. More >>